AKA Project Farfemmuven
Over designed and based on 8′ long x 2, 6′ wide x 2 with 4 x 2.5′ risers.
4″x4″x16′ non-treated (8′ x 2) $15
4″x4″x12′ non=treated (6′ x 2) $12
4″x4″x10′ non-treated (2.5′ x 4) $ 10
2″x4″x8′ non-treated x 2 $ 6
BC4 Post Cap Braces x 8 $35
#10 x 1.5″ Hex Head Screws (SKU 479710) $12
3″ Steel Casters (300lbs x 4 SKU 194425) x 4 $22
GRAND TOTAL $112
FROM: http://www.shoptalkforums.com/viewtopic.php?f=19&t=144363&start=15
I first braced the doors with some 2X4’s and metal strips, not pretty but it works and was cheap. Luckily there is no pressure on them after raising the body and the heater channels look to be free of rust.
![IMG_3369[1]](http://www.73ghia.com/wp-content/uploads/2014/07/IMG_33691.jpg)
I used 4×4’s, some I had laying around from a deck/fence project that took priority over working on the car earlier in the month. I used 8′ lengths for the lower sections and 6’5″ for the width to allow wider tires when I eventually get to that point. The vertical pieces are 2′ (the OP later said he would add 4 inches to those 2 foot sections) and allowed the pan to almost completely clear the body with the front suspension attached. I removed that and put it on dolly’s a bit lower that allowed full clearance.
![IMG_3370[1]](http://www.73ghia.com/wp-content/uploads/2014/07/IMG_33701.jpg)
I bet I could make one of these.
This will definitely be needed to restore this ol’ gal.
Part ………….ft-lb …….size (dia x pitch)
Engine
Connecting rod nut -24 -m 9×1
Connecting rod capscrew -32 -m 9×1
Crankcase nut -14 -m8
Crankcase nut -25 -m 12×1.5
Cylinder head nut -8 -mm 18 m 8
Cylinder head nut -10- mm 23 m 10
Rockershaft nut -18 -m 8
Heat Exchanger at head -14- m 8
Muffler Clamp bolts -7 -m 6
Intake manifold nut -14 -m 8
Preheat-flange bolt -7 -m 6
Oil Pump nut -14 -m 8
Oil Pump nut -9 -m 6
Oil Drain plug -25- m 14×1.5
Oil Strainer nut -5 -m 6
Oil cooler nut -5 -m 6
Oil filler gland nut- 40
Flywheel Gland nut -235 -m 28×1.5
Clutch bolt -18 -m 8×1.5
Sparkplug -25 m -14×1.25
Engine to trans nut -22 -m 10
Crossmember bolt -18 -m 8
Crossmember bolt -29 -m 10
Generator pulley nut -43 -m 12×1.5
Fan nut -43 -m 12×1.5
Crankshaft pulley nut -32 -m 20×1.5
Crossmember to body -18 -m 8
Fan/Crankshaft pulley -94-108 -m 20×1.5
Front Axle and Steering
Front Beam to pan bolts -36
Body to beam bolts -14
Shock to beam sideplate -14-m 10
Shock to beam sideplate -25- m 12
Shock to lower torsion arm -25
Steering damper to front beam bolt -32
Steering damper to tie rod -18
Tie rod to castle nut -18
Tie rod nut -18
Clamp for tie rod bolt -11
Lock nut for torsion set screw -36
Wheel bearing clamp screw -10
Steering ball joint to knuckle -51
Steering box to front beam -22
Steering coupler to worm shaft -18
Pitman arm to shaft bolt -51
Locknut for pitman arm adj screw -18
Lock nut for worm spindle adj screw -42
Steering box housing cover bolt -18
Canceling ring to steering wheel -3.5
Steering wheel nut -36
Steering column to dash bolts -7
Column switch to attach plate -7
Column switch clamp to housing -7
Steering coupling flange to disc -11
Column to couple flange bolt -11
Manual Transaxle
Drive pinion round nut ball bearing -87
Drive pinion round nut roller bearing -144
Pionion retainer nut -36
Pinion nut -43
Drive shaft nut -43
Reverse lever guide bolt -14
Selector fork bolt -18
Gearshift housing nuts -11
Ring gear bolts – 43
Final drive cover nuts -22
Axle tube retainer nuts -14
Rear wheel bearing retainer nut -43
Oil drain plug -14
Oil filler plug -14
Rear axle shaft nut -217
Transaxle to frame bolt -166
Master cylinder
Stop screw in housing bolt -7
Residual pressure valve to housing -14
Brake light switch -14
Master cylinder to to frame bolts -18
Brake line to master cylinder -18
Front Brakes
Splash sheild to steering knuckle bolts -7
Wheel cylinder to backing plate -18
Caliper housing screw (disc brake) -18
Backing plate bolt -36
Caliper mounting bolts (disc brake) -29
Bleeder valve -9
Clamp nut screws -9
Hose to wheel cylinder/caliper -14
Rear Brakes
Wheel cylinder to backing plate- 22
Bearing housing bolts -43
Brake drum to axle bolt -253
Lug nut 14mm -94
Lug nut 12mm -72
Pedal assembly
Pedal bracket to frame -32
Pedal stop to frame bolts -18
